+44 (0)1932 564391

sales@stanhope-seta.co.uk
Find your local representative

Seta Oil Test Centrifuge - 6 place

Part Number 90100-0

The Seta Oil Test Centrifuge is a heated chamber centrifuge used to determine water and sediment in oils. The large diameter chamber, with six place rotor and cushioned adaptors allows the use of 6 and 8 inch conical, pear-shaped, trace sediment and 12.5 ml tubes.

The swing out rotor ensures that samples are held near vertical when at rest allowing precise measurement of sediment. The centrifuge features a hinged lid that opens to the fully upright position to allow easy loading and unloading of tubes between tests.

Speed, temperature and timing are microprocessor controlled. Run parameters are entered via a liquid proof 'touch panel' and digital display.

Click here for 4-place Centrifuge

Bio fuel compatibleBio fuel compatible
'Setaalert' remote monitoring compatible'Setaalert' remote monitoring compatible

ADDITIONAL INFORMATION

Precise heating for accurate results
Isothermal heaters fitted internally to the centrifuge chamber give precise temperature control to within +/-1 C.

Fast and easy operation
9 programme memories allow a user to configure the instrument to automatically operate to the specified test parameters, saving time, easing operation and assisting repeatability. A 'Quick Run' mode allows short runs of up to 99 seconds.

Safety features
A motor driven lid latch with a safety interlock prevents the centrifuge operation while the lid is unlocked. Imbalance detection and over-temperature protections protects the motor and chamber from damage.

Setafuge Hazard Reduction System
The optional Setafuge Hazard Reduction System (90010-0) can be fitted into the centrifuge to extract vapours from the chamber and significantly reduce vapour hazards.

Supplied with;
Rotor
Buckets and cushions

SPECIFICATIONS

Maximum Relative Centrifugal Force (RCF) 2210 g
Maximum Rotational Speed 3000 rpm
Temperature Range Ambient +5 C in the range of 20 to 80 C (1 C steps)
Timer Range 10 sec to 100 hours or continuous operation
Control Microprocessor with 99 memory capacity
Capacity 6 Samples
Voltage Range 230 Vac, 50/60 Hz (Optional transformer for 110/120 V)
Power 950 W
Size (HxWxD) 410 560 640 mm
Weight 72.5 kg
CCCN Code: Tariff 84211920

DETAILS OF METHODS

ISO 9030The Oil Test Centrifuge is a microprocessor controlled, programmable, heating centrifuge that meets the above standards
ASTM D91Standard test method for precipitation number of lubricating oils
ASTM D893Standard test method for insolubles in Used Lubricating Oils
ASTM D1290Standard test method for sediment in water-emulsion polishes by centrifuge
ASTM D1796Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D2273Standard Test Method for Trace Sediment in Lubricating Oils
ASTM D2709Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D2711Standard Test Method for Demulsibility Characteristics of Lubricating Oils
ASTM D4007Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure)
ISO 3734Petroleum products - Determination of water and sediment in residual fuel oils - Centrifuge methods
Seta Oil Test Centrifuge ASTM IP

FEATURES

6 place swing out rotor
Static, near vertical bucket positioning
Specifically designed for testing oils
Heated chamber, ambient to 80 C
Pre-heat facility to ensure bowl is at test temperature prior to test
Universal buckets for 12.5 ml, 6 and 8 inch glassware
Microprocessor control with 99 memories
Optional trolley

METHODS

ASTM D1290, ASTM D1796, ASTM D2273, ASTM D2709, ASTM D2711, ASTM D4007, ASTM D893, ASTM D91, ISO 3734, ISO 9030

INDUSTRIES

Petroleum - Fuels & Oils

Crude Oil

Biodiesel

Lubricants

Copyright Stanhope–Seta Limited 2014